Skimcrete CP Feather and Patch 55 lb Bag

(No reviews yet) Write a Review
Skimcrete CP
If you need more than we currently have listed, please contact us at 1-844-309-2945!

Product Overview

SKIMCRETE® CP is a high performance repair mortar.

SKIMCRETE® CP is easy to work with and is compatible with both interior and exterior applications. With its capability to withstand extreme temperatures SKIMCRETE® CP is ideal for fast track projects in high traffic areas including streets and truck docks.
SKIMCRETE® CP is open to standard traffic within 4 hours of application and can be applied as thin as 1/4”.

Freight Quote - 1-844-309-2945

This is a naturally heavy or large item. If you need to order in quantity, or believe it may be more cost effective to ship it by freight give us a call so we can get you a freight quote

 Warehouses -Vertical Repairs- Sidewalks- Parking Lots- Highways -Truck Docks Heavy Industrial Repairs- Roads- Commercial Floors- Ramps- Mud Bed
Features & Benefits:
 Fast Curing- High Strength- Interior and exterior applications - One component- Gains strength quickly- Compatible with a wide range of temperatures - Superior bond - Better coverage -Resistant to freeze and thaw conditions
Packaging 55 lb Double Wall Bag
Preparation and Application:
 Concrete Floors The concrete surface should be clean and sound. The surface should be free of any bond breakers including but not limited to loose gravel, oil, wax, grease or dirt. If a bonding agent is not used the concrete should be presoaked and saturated surface-dry SSD condition without standing water.

 Once surface is prepared immediately place the repair mortar on the prepared area working it firmly into the bottom ensuring a good bond
 1. Use a minimum 1/2” slow speed drill and mixing paddle or an appropriately sized mortar mixer. Do not mix by hand.
2. For every 55 lbs a 1/2 gallon of water may be used. DO NOT over water.
3. Mix for 3-5 minutes adding powder to the water. Do not over mix due to the formation of air bubbles. For deeper patches SKIMCRETE CP may be extended by adding up to 30 lbs of clean pea gravel. Small additional water may be added only after 2 minutes of mixing; no more than one cup.
4. If patches are less than 1” deep keep the work neat. For deeper patches SKIMCRETE CP may be extended up to 30 lbs using pea gravel.
5. SKIMCRETE CP can accept epoxy after 6 hours.

 Clean Up:
 Use water to clean SKIMCRETE CP of tools and equipment. Once it is dry it will need to be removed mechanically. It is important to periodically clean tools.

 For Best Performance:
 In order to get the maximum performance keep the materials at 72ºF for 24 hours. Keep the materials from wind, sunlight and other weather conditions that could alter the drying time.
Do not apply less than 1/4” in thickness or where featheredge is needed.
 Keep product stored between 50°F – 90°F
Proper application is the responsibility of the user.
Call customer service at 1-877-514-5336 with any questions or technical recommendations.

 Do not use… • Where hydrostatic pressure (water) exists or moisture emissions exceed level permitted for installing floor covering.
• Over presswood, particle board, masonite, chipboard, OSB, underlayment board not of APA Underlayment (exterior) grade or similar dimensionally unstable materials susceptible to movement or swelling.
 • Over gypsum based patches or underlayment material due to chemical reaction.       • Single layer stripwood floors.

WARNING CAUSES SKIN IRRITATION. INJURIOUS TO EYES. Contains standard portland cement and silica. Do not breathe dust. Dust can cause delayed lung injury (Silicosis). Use in a well ventilated area or wear a properly fitted NIOSH/MSHA approved respirator. Avoid eye contact. In case of eye contact, flush with water a minimum of 15 minutes. Consult a physician immediately. Avoid prolonged contact with skin. Wash thoroughly after handling.


(No reviews yet) Write a Review